工業冷水機機組應用廣泛，在有工業的地方就要用到冷水機設備，如：化工冷水機、電鍍冷水機、食品冷水機、電子加工冷水機、模具冷水機、印刷冷水機等，而且大部分行業對于工業冷水機要求很高的，大部分客戶的要求都是24小時運轉，所以對冷水機的電源電壓要求也很高，如果冷水機的幾相電壓不平衡太于2%時，操作時有可能損壞冷水機，所以要控制好冷水機。
冷水機電源電壓的檢測
如果冷水機標準電壓為3相，380V，50Hz，測得UAB=376V，UAC=379V，UBC=385V。得出平均電壓=(376+379+385)/3=380V：確定與平均電壓的偏差值：△UAB=380-376=4V，△UAC=380-379=1V，△UBC=385-380=5V，最大偏差值為5V，5/380=1.3%，得出最大相電壓不平衡為1.3%。
如果測得該電源和電壓在正常范圍內，這樣就可以正常開機。如果冷水機電源控制不好，那么損壞的話就會有很高的一個維修成本，按正常來講的話電壓都會比較正常。
冷水機的電源電壓最大可允許的相電壓不平衡為2%，相電流不平衡為10%。注：當相電壓不平衡大于2%，絕對不能開機操作。
冷水機的工作電源是3相，380V，50Hz。在運行冷水機前，需要檢查電控柜中電源部分和控制部分有無異常，并固緊接線端子，包括總電源接線銅排，自動空氣斷路器(空氣開關)，Δ-Δ或Y-Δ壓縮機啟動電氣裝置，PLC觸摸屏，靶流開關，冷凍水泵，冷卻水泵聯動控制線(控制接點為無源接點)，溫度傳感器，冷凍，冷卻水泵，冷卻水塔聯動控制線(控制接點為無源接點)，電控儀表等等節點。待確認好后，方可執行開機操作，確保冷水機組正常運行。
冷水機組屬于大功率機器，電壓基本都是工業電壓，380V，所以在安裝冷水機時最好安裝穩壓器。